Universal Carbon Monoxide Alarm CD 9775 User Manual

MODEL CD-9775  
SMOKE & CARBON MONOXIDE ALARM  
WITH SILENCE CONTROL  
E
READ ALL INSTRUCTIONS  
The smoke alarm uses an extremely small amount of a radioactive element in the ionization  
chamber. Do not tamper with radioactive sealed source or try to repair the smoke alarm  
yourself. Refer to instructions for repairs.  
LIMITATIONSAND FUNCTIONS  
This combination smoke/carbon monoxide (CO) alarm requires constant 120VAC power to  
operate properly.  
THERE ARE TWO BASIC SMOKE ALARM TYPES - IONIZATION AND PHOTOELECTRIC.  
Ionization smoke alarms (such as this smoke alarm) are your best overall choice for  
reliability and fast response time, since they quickly sense small "invisible" smoke particles  
and will also sense larger "visible" smoke particles. Photoelectric smoke alarms may  
respond more quickly in certain types of fires, for example - slow smoldering fires with large  
"visible" smoke particles. ALL TYPES OF SMOKE ALARMS HAVE LIMITATIONS. NO TYPE  
OF SMOKE ALARM CAN SENSE EVERY KIND OF FIRE OR SMOKE EVERY TIME.  
SMOKE ALARMS can sound an alarm only when smoke reaches their sensors. Smoke may  
not reach the smoke alarm QUICKLY ENOUGH to ensure safe escape. They do not sense  
heat, flame or gas (propane).  
ALL alarms have limitations. This combination smoke/CO alarm is not foolproof and is not  
warranted to protect lives or property. It is not a substitute for insurance.  
WARNING - SINCE A SMOKE OR CO ALARM WILL NOT WORK WITHOUT POWER, having an  
alarm(s) that works from two completely different power sources, such as an AC direct wire with  
battery backup can give you an extra measure of protection in case of an AC power failure or a dead  
battery.  
CO ALARMS are designed to detect carbon monoxide gas from any source of combustion  
that reaches their sensor. They are NOT designed to detect any other type of gas.  
USING A SMOKE ALARM IN A SMOKY AREA LIKE A KITCHEN, OR IN A HIGH HUMIDITY  
AREA NEAR A SHOWER, CAN CAUSE FALSE ALARMS. DO NOT TURN OFF THE AC  
POWER TO QUIET THE ALARM. A SMOKE ALARM WILL NOT HELP PROTECT YOU IF IT  
IS NOT POWERED. Properly locate your alarm to avoid nuisance alarms.  
A SMOKE ALARM MAY NOT ALWAYS WARN YOU ABOUT FIRES CAUSED BY  
CARELESSNESS AND SAFETY HAZARDS LIKE SMOKING IN BED, VIOLENT  
EXPLOSIONS, ESCAPING GAS, IMPROPER STORAGE OF FLAMMABLE MATERIALS,  
OVERLOADED ELECTRICALCIRCUITS, CHILDREN PLAYING WITH MATCHES, NATURAL  
CAUSES SUCH AS LIGHTNING, OR ARSON. FIRE PREVENTION IS YOUR BEST  
SAFEGUARD.  
SMOKE ALARMS CANNOT DETECT FIRES IF THE SMOKE DOES NOT REACH THEM.  
Smoke from fires may not reach the sensing chamber and set off the alarm. One unit should  
be installed inside each bedroom or sleeping area.  
SMOKE ALARMS MAY NOT DETECT FIRE ON ANOTHER FLOOR OR AREA OF THE  
HOME. Recommended minimum protection is at least one unit in every sleeping area and  
every bedroom on every level of your home. Interconnected units may provide earlier  
warning than stand-alone units since all units alarm when one detects smoke.  
ALARMS MAY NOT BE HEARD. The alarm horn in this unit meets or exceeds current  
standards, but it may not be heard if: (1) the unit is located outside a closed or partially  
closed door; (2) residents recently consumed alcohol or drugs; (3) the alarm is drowned out  
by noise from stereos, TV's, air conditioners or other appliances or (4) if residents are hearing  
impaired or sound sleepers.  
Because it is possible for the alarm to fail at any time, you must test the alarm weekly and  
replace it every 7 years.  
SMOKE ALARMS ARE NOT TO BE USED WITH DETECTOR GUARDS UNLESS THE  
COMBINATION HAS BEEN EVALUATED AND FOUND SUITABLE FOR THAT PURPOSE.  
CURRENT STUDIES HAVE SHOWN SMOKEALARMS MAY NOTAWAKENALL SLEEPING  
INDIVIDUALS AND THAT IT IS THE RESPONSIBILITY OF INDIVIDUALS IN THE  
HOUSEHOLD WHO ARE CAPABLE OF ASSISTING OTHERS TO PROVIDE ASSISTANCE  
TO THOSE WHO MAY NOT BE AWAKENED BY THE ALARM SOUND OR TO THOSE WHO  
MAY BE INCAPABLE OF SAFELY EVACUATING THE AREA UNASSISTED.  
 
WHAT YOU SHOULD DO IF THE SMOKE ALARM SOUNDS  
YOU MUST QUICKLY DO THE FOLLOWING:  
If the smoke alarm sounds and you have not pushed the test button, it is a warning of a  
dangerous situation.  
Your immediate response is necessary. To prepare for such occurrences, develop family  
escape plans, discuss them with ALL household members and practice them regularly.  
BASICS OF ESCAPE PLAN  
o
Make a floor plan indicating all doors and windows and at least two escape routes from each  
room. Second story windows may need a rope or chain ladder.  
o
Have a family meeting and discuss your escape plan, showing everyone what to do in case of  
fire.  
o
o
Determine a place outside your home where all of you can meet if a fire occurs.  
Familiarize everyone with the sound of the smoke alarm and train them to leave your home when they  
hear the sound.  
o
o
Identify children's bedrooms with red stickers placed in the upper left corner of the windows. They  
are available from your local fire department.  
Practice a fire drill at least every six months. Practice allows you to test your plan before an  
emergency. You may not be able to reach your children. It is important they know what to do!  
WHAT TO DO WHEN THE SMOKE ALARM SOUNDS  
o
Leave immediately by your plan of escape. Every second counts, so don't waste time getting  
dressed or picking up valuables.  
o
In leaving, don't open any inside door without first feeling its surface. If hot, or if you see smoke  
seeping through cracks, don't open that door! Instead, use your alternate exit. If inside door is  
cool, place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke  
rush in.  
o
o
o
o
Stay close to the floor if air is smoky. Breathe shallowly through a cloth, wet if possible.  
Once outside, go to your selected meeting place and make sure everyone is there.  
Call the fire department from your neighbor's home – not from yours!  
Don't return to your home until fire officials say that it is all right to do so.  
IMPORTANT CONSIDERATIONS  
YOUR COMBINATION SMOKE/COALARM HAS BEEN DESIGNED WITHAN END-  
OF-SERVICE LIFE OFAPPROXIMATELYSEVEN YEARS OF OPERATION FROM  
INITIALPOWER UP.  
NOTE:MANUFACTURERRECOMMENDSREPLACEMENTOFYOURALARMSEVEN  
YEARSAFTER DATE OF INSTALLATION.  
Activation of this device indicates the presence of carbon monoxide  
(CO) which can kill you. If the CO alarm sounds:  
1. Operate test/reset button;  
(Phone No.  
)
2. Call your emergency services, fire department or 911;  
3. Immediately move to fresh air - outdoors or by an open door/window. Do a head count  
to check that all persons are accounted for. Do not reenter the premises nor move  
away from the open door/window until the emergency services responders have arrived,  
the premises have been aired out, and your alarm remains in its normal condition.  
4. After following steps 1-3, if your alarm reactivates within a 24 hour period, repeat steps  
(Phone No.  
)
1-3 and call a qualified appliance technician;  
to  
investigate for sources of CO from fuel burning equipment and appliances and inspect  
for proper operation of this equipment. If problems are identified during this inspection,  
have the equipment serviced immediately. Note any combustion equipment not  
inspected by the technician and consult the manufacturers' instructions or contact the  
manufacturer(s) directly for more information about CO safety and this equipment.  
Make sure that motor vehicles are not, and have not been, operating in an attached  
garage or adjacent to the residence.  
Page 3  
 
INSTALLING THE COMBINATION SMOKE/CO ALARM  
FOR RESIDENTIAL USE  
LOCATION  
Before installing your combination smoke/CO alarm, it is important to choose the best  
locations in your home. Placement can affect how well the alarm performs and how well  
residents hear the alarm if it sounds. Statistics of the National Fire Protection Association  
(NFPA) show that most of the fatal CO occurrences happen at night while people are  
sleeping.  
Early warning of CO is best achieved by the installation of CO alarms on all floors and  
areas of the household.  
RECOMMENDATIONS  
– Put a CO alarm inside each bedroom where the occupant closes the door while sleeping.  
Particulate smoke can be blocked by a closed door, but CO fumes are likely to get  
through.  
– A CO alarm should be installed between 5 and 20 feet from potential sources of CO in  
any family living unit containing a fuel-burning appliance or fireplace or having an attached  
garage.  
– A combination smoke/CO alarm should be centrally located outside of each separate  
sleeping area in the immediate vicinity of the bedrooms. Where bedrooms are separated  
and audibility of the alarm to occupants within the bedroom area could be seriously  
impaired, more than one unit could be needed.  
– If a bedroom area hallway is more than 30 feet long, install a smoke alarm at each end.  
– Alarms can alert you to a problem only after smoke or CO reach their sensors. Choose  
locations free of obstructions, where the alarm will stay clean and protected from adverse  
environmental conditions.  
– Install a smoke or combination alarm on the basement ceiling at the bottom of the stairwell.  
– Make sure the alarms can be easily heard from multiple locations throughout the home.  
– This combination smoke/CO alarm makes it easy to provide both types of protection  
throughout the home.  
– This combination smoke/CO alarm is designed to be used in single-family homes. It  
alone may not meet requirements for multiple-resident dwellings (apartment buildings,  
boarding houses, hotels or motels).  
FIGURE 2  
Page 4  
 
Existing Homes:  
The NFPArequires a smoke alarm on every level and outside each sleeping area in existing construction. An  
existing household with one level and one sleeping area is required to have one smoke alarm.  
New Construction Homes and Manufactured Homes:  
The NFPArequiresAC-powered, interconnected smoke alarms to be installed inside each bedroom, outside each  
bedroom area, and on every level of the home. They also require a minimum of two AC-powered, interconnected  
smoke alarms in any new construction home.  
Sloped Ceilings (Peaked Ceilings):  
Smoke alarms or smoke detectors mounted on a peaked ceiling shall be located within 36 in. (914 mm) horizontally  
of the peak, but not closer than 4 in. (102 mm) vertically to the peak.  
Sloped Ceilings (Shed Ceilings):  
Smoke alarms or smoke detectors mounted on a sloped ceiling having a rise greater than 1 ft. in 8 ft. (1 m in 8  
m) horizontally shall be located within 36 in. (914 mm) of the high side of the ceiling, but not closer than 4 in. (102  
mm) from the adjoining wall surface.  
Tray-Shaped Ceilings:  
Smoke Alarms or smoke detectors shall be installed on the highest portion of the ceiling or on the sloped portion  
of the ceiling within 12 in. (305 mm) vertically down from the highest point.  
Mobile Home Installation:  
For minimum protection, smoke alarms should be installed in compliance with H.U.D. Manufactured Home  
Construction Safety Standards, Title 24 CFR, Section 3280.208 and Section 3282. For additional protection, see  
Single Story Residence smoke alarm requirements/recommendations for Existing Homes and New Construction  
Homes.  
Note: For mobile homes built before 1978, install smoke alarms on inside walls between 4” and 12” from the  
ceiling (older mobile homes have little or no insulation in the ceiling). This is especially important if the ceiling  
is unusually hot or cold.  
Install a smoke alarm inside each bedroom and in the hallway outside each separate sleeping area.  
AVOID THESE LOCATIONS  
the garage – products of combustion are present when you start your automobile.  
in areas with high humidity, like bathrooms or areas near dishwashers or washing machines.  
Install at least 3 feet (0.9 meters) away from these areas.  
in areas of turbulent air such as air returns or heating and cooling supply vents. Install at least  
3 feet (0.9 meters) away from these areas.  
in extremely dusty, dirty or insect-infested areas. Loose particles interfere with smoke alarm  
operation.  
in areas where temperature may fall below 400F (4.40C) or rise above 1000F (37.80C).  
closer than 5 feet (1.5m) from fluorescent lights, electrical "noise" and flickering may affect  
the alarm's operation.  
do not locate this alarm within 5 feet (1.5m) of any cooking appliance.  
in areas of reverse venting of fuel burning appliances caused by outdoor ambient conditions,  
such as:  
-
wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/  
humid air with extended periods between cycles).  
-
-
-
-
-
-
-
negative pressure differential resulting from the use of exhaust fans.  
simultaneous operation of several fuel burning appliances competing for limited internal air.  
vent pipe connections vibrating loose from clothes dryers, furnaces or water heaters.  
obstructions in or unconventional vent pipe designs which can amplify the above situations.  
extended operation of unvented fuel burning devices (range, oven, fireplace, etc.).  
temperature inversions which can trap exhaust gasses near the ground.  
car idling in an open or closed attached garage or near a home.  
to reduce the possibility of nuisance tripping of the alarm’s alarm circuit, accommodation  
spaces are to be well ventilated when household cleaning supplies or similar contaminants are  
used.  
Page 5  
 
THIS COMBINATION SMOKE/CO ALARM WILL NOT WORK WITHOUT A GOOD  
BATTERY PROPERLY INSTALLED. THE ALARM SHOULD BE TESTED WHEN  
INSTALLED AND THEN TESTED WEEKLY AFTER THAT.  
INSTALLATION AND OPERATION  
INSTALLATION INSTRUCTIONS: CAUTION!! READ CAREFULLY.  
CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!  
This combination smoke/CO alarm requires a working 9 Volt battery to operate properly. This  
combination smoke/CO alarm WILL NOT work if the battery is removed, drained or improperly  
connected. DO NOT use any other kind of battery except as specified in this manual.  
NOTE: AC/DC combination alarms offer added protection in the event of a power failure or a  
drained battery.  
Test alarm immediately following installation and weekly for proper operation by pushing  
the test button. The alarm will then test itself for proper operation. The alarm then resumes  
normal operation.  
A mounting plate is provided on the back of the alarm.  
Remove the mounting plate from the back of the alarm by holding the mounting plate and  
twisting the alarm in the direction indicated by the "TURN TO REMOVE" arrow on the side of the  
alarm base.  
TAMPER LOCKING PIN: To make your alarm somewhat tamper resistant, a locking pin has been  
provided (break-away part of mounting plate). Using this tamper pin will deter children and others  
from removing the alarm from the mounting plate. To use the tamper pin, insert it into the hole in  
the side of the alarm after the alarm has been installed on the mounting plate. Using long nose  
pliers, pull the tamper pin out of the hole. It is now possible to remove the alarm from the mounting  
plate.  
The combination smoke/CO alarm is designed for easy mounting on wall or ceiling. A complete  
mounting kit is included with the alarm. First, attach the mounting bracket on the wall or ceiling with  
the screws and anchors provided. Second, push and turn the alarm clockwise on the mounting  
bracket. (Note: Your smoke alarm is equipped with a safety device which prevents mounting  
unless a battery is installed. If alarm will not lock into the mounting bracket, check to make sure  
a battery is installed.)  
1. To activate 9 volt battery and alarm, hold the QUICK DRAWTM pull-out battery drawer closed,  
pull and remove the PULL-TAB. Discard PULL-TAB.  
NOTE: After initial battery power up, the Green LED will flash on rapidly approximately 20  
times and then remain off. Proceed to test the alarm.  
2. See "TAMPER LOCKING PIN."  
3. Press the TEST/SILENCE button. Check the LED's for proper operation (see "TESTING  
YOUR ALARM"). After test sequence, the Green LED flashes on approximately every 40  
seconds to indicate proper operation.  
OPERATION, TESTING & MAINTENANCE  
OPERATION: The alarm is operating once the power is connected (the battery must be installed).  
SMOKE/COMBUSTION PRODUCTS ALARM CONDITION: When products of combustion are  
sensed, the unit sounds a loud SMOKE alarm pattern which continues until the air is cleared. For  
the SMOKE alarm pattern, this alarm incorporates the internationally recognized horn signal for  
evacuation. During smoke alarm mode, the horn produces three beeps followed by a two second  
pause and then repeats. The Red LED will flash on simultaneously with the horn pulses.  
CARBON MONOXIDE ALARM CONDITION: When CO is sensed at a high level or at a low level  
for a lengthy period of time, the unit sounds a loud CO alarm pattern (4 short horn pulse, pause,  
repeat) for 4 minutes then 1 minute of silence. This alarm pattern continues until the air is cleared  
or the alarm is reset. The Red LED will flash on simultaneously with the horn pulses.  
NOTE: To reduce the possibility of nuisance tripping of the alarm's alarm circuit, accommodation  
spaces are to be well ventiliated when household cleaning supplies or similar contaminants are  
used.  
TESTING YOUR ALARM: Test alarm weekly for proper operation by pushing, then releasing, the  
TEST/SILENCE button. The alarm will then test itself for proper operation of BOTH the SMOKE  
and CO detection and alarm circuits. The Red LED will begin to flash rapidly and the alarm will  
indicate two cycles of the SMOKE alarm pattern. The Red LED will simultaneously flash during the  
SMOKE alarm pattern. This will be followed by two cycles of the CO alarm pattern, during which  
the Red LED flashes on simultaneously with the horn pulses.  
Page 6  
 
STANDBY (NON-ALARM) CONDITION: Whenever battery power is present, the Green LED is  
off and flashes on approximately every 40 seconds and the Red LED is off.  
(ALARM) CONDITION: For BOTH the SMOKE and CO alarm conditions, the Red LED flashes on  
and the unit emits a loud, pulsating alarm (refer to the OPERATION section to differentiate  
between the SMOKE and CO alarm patterns).  
RESETTING YOUR ALARM: Reset your alarm by momentarily pushing the "TEST/SILENCE"  
button.  
END-OF-SERVICE LIFE CONDITION: When the alarm sounds 4 chirps every 30 seconds and  
the yellow service light flashes 1 time during the first chirp, it indicates the “End-of-Service Life”  
of the alarm. This alarm signal cannot be reset. The alarm should be replaced immediately.  
NEVER use an open flame of any kind to test this unit. You might accidentally damage or set  
fire to the unit or to your home. The built-in test switch accurately tests the unit's operation  
as required by Underwriters Laboratories Inc. (UL).  
If you choose to use an aerosol smoke product to test the smoke alarm, be certain to use one  
that has been Listed to Underwriters Laboratories, Inc. Safety Standards and use it only as  
directed. Use of non-UL Listed products or improper use of UL Listed products may affect  
the smoke alarm's sensitivity.  
Before using the alarm "test/silence" feature, identify the source of smoke or CO and be  
certain that safe conditions exist.  
FALSE ALARMS "TEST/SILENCE" CONTROL: Units with the "silence" feature have the capability  
of temporarily reducing the sensitivity of the smoke alarm circuit for approximately 3-9 minutes. This  
feature is to be used only when a known alarm condition such as smoke from cooking activates the  
smoke alarm. The smoke alarm "silence" feature is activated by pushing the Test/Silence button on  
the smoke alarm cover for at least three seconds. The smoke alarm will automatically reduce sensitivity  
and the Red LED will flash on every 6 seconds and "beep" sounder approximately every 36 seconds  
for approximately 3-9 minutes to indicate the alarm is in the temporary silent condition. The smoke  
alarm will gradually regain normal sensitivity and sound the alarm if particles of combustion are still  
present. The "silence" feature may be used repeatedly until the air has cleared.  
MAINTENANCE: This combination alarm is virtually maintenance free. However, under dusty  
conditions, a vacuum hose may be used to clear the sensing chamber of dust.  
Clean the alarm at least once a month to remove dust, dirt or debris. Using a soft brush or wand  
attachment to a vacuum cleaner, vacuum all sides and cover of alarm. Be sure all the vents are  
free of debris.  
END-OF-SERVICE LIFE NOTIFICATION: A majority of home fire deaths are a result of no smoke  
alarms or no working smoke alarms. In addition to the “replace by date” stamped on the back of  
your alarm, your alarm contains a unique audible end-of-service life notification feature. When it  
is time to replace your alarm, which is approximately 7 years of operation, i.e. from initial power  
up, the alarm will sound 4 chirps every 30 seconds and the yellow LED will blink on in synch with  
the first chirp. The green LED stays on. This alarm signal cannot be reset. The alarm should be  
replaced immediately.  
The outside of the alarm can be wiped with a damp cloth. Do not use any household cleaning  
agents, ammonia-based cleaners, paints, varnishes or any other chemical on or near your alarm.  
AFTER CLEANING, REINSTALL YOUR ALARM. TEST YOUR ALARM BY USING THE TEST  
BUTTON.  
SERVICE CONDITION: Periodically, the alarm's circuitry is tested. If an error is detected, the  
alarm will sound a double "beep" and the Yellow LED will flash on twice approximately every 40  
seconds. If this occurs, reset your alarm by momentarily pushing the "TEST/SILENCE" button.  
If the smoke/CO alarm is false alarming or indicating service and cannot be restored to normal  
operation, the alarm should be replaced.  
Page 7  
 
BACKUP BATTERY REPLACEMENT  
This alarm uses a 9 Volt Alkaline battery. The battery should last for at least one year under normal  
operating conditions. The alarm has a low battery indicator, an audible "beep." It will operate at 30-  
40 second intervals for a minimum of 7 days. When this indication occurs, replace the battery with  
an Alkaline type (Eveready Energizer #522, Duracell #MN1604), or Lithium type (ULTRALIFE U9VL-  
J), from your local retailer. Use the convenient QUICK DRAWTM pull-out battery drawer for easy  
battery replacement.  
Slide the QUICK DRAWTM pull-out battery drawer open and remove the battery. While observing  
polarity, push the replacement battery into the battery drawer until it is held securely in place. Carefully  
close the QUICK DRAWTM pull-out battery drawer.  
Use only the batteries specified. Use of different batteries may have a detrimental effect on  
the alarm. The constant exposures to high or low temperatures or high humidity may reduce  
battery life.  
When battery door is open, the battery will not power the alarm even if the battery is properly  
installed.  
Do not attempt to repair this combination alarm. Doing so will void your warranty.  
REPAIRS AND SERVICES  
The smoke alarm contains less than 1 microcurie (37 kilobecquerel) of Americium 241, a radioactive  
material. The distribution of these ionization type smoke alarms is licensed by the U.S. Nuclear  
Regulatory Commission; the consumer is exempt from any licensing or requirements. If the  
smoke alarm is defective in any way, do not tamper with the unit. Return the unit for servicing. (See  
warranty for instructions or in-warranty returns.) There will be a service charge for repairing out of  
warranty units.  
NATIONAL FIRE PROTECTION ASSOCIATION REQUIRED PROTECTION  
For your information, the National Fire Protection Association's Standard 72, reads as follows:  
“11.5.1 One- and Two-Family Dwelling Units. 11.5.1.1 Smoke Detection. Where required  
by applicable laws, codes, or standards for the specified occupancy, approved single-  
and multiple-station smoke alarms shall be installed as follows: (1) In all sleeping  
rooms. Exception: Smoke alarms shall not be required in sleeping rooms in existing  
one- and two-family dwelling units. (2) Outside of each separate sleeping area, in  
immediate vicinity of the sleeping rooms. (3) On each level of the dwelling unit,  
including basements. Exception: In existing one- and two-family dwelling units, approved  
smoke alarms powered by batteries are permitted.  
“A.11.8.3Are More Smoke Detectors Desirable? The required number of smoke detectors  
might not provide reliable early warning protection for those areas separated by a door  
from the areas protected by the required smoke detectors. For this reason, it is  
recommended that the householder consider the use of additional smoke detectors for  
those areas for increased protection. The additional areas include the basement,  
bedrooms, dining room, furnace room, utility room, and hallways not protected by the  
required smoke detectors. The installation of smoke detectors in kitchens, attics  
(finished or unfinished), or garages is not normally recommended, as these locations  
occasionally experience conditions that can result in improper operation.”  
The equipment should be installed using wiring methods in accordance with the National Fire  
ProtectionAssociation’s Standard 72, Chapter 11. (National Fire ProtectionAssociation, Batterymarch  
Park, Quincy, MA 02269).  
THIS PRODUCT IS LISTED TO UL STANDARD FOR SAFETY,  
UL217, BY UNDERWRITERS LABORATORIES  
Page 8  
 
UNIVERSAL FIVE YEAR LIMITED WARRANTY  
UNIVERSAL SECURITY INSTRUMENTS, INC. ("USI") warrants your  
USI product to be free from defects in material and workmanship  
for a period of five (5) years from the date of purchase. This  
warranty applies only to the original consumer purchaser and only to  
products used in normal residential use and service. If this product is  
found to be defective, USI's only obligation, and your exclusive remedy,  
is the repair or replacement of the product, at USI's discretion, provided  
that the product has not been damaged through misuse, abuse,  
accident, modifications, alteration, neglect or mishandling. This  
Warranty shall not apply to any product which is found to have been  
improperly installed, set-up, or used in any way not in accordance with  
the instructions supplied with the product. This warranty shall not apply  
to any batteries used in the product or to any damage which may be  
caused by such batteries. For replacement of this product under the  
terms of this Warranty, contact our Customer Service line at 1-800-  
390-4321, Ext. 238, for current postage and handling fees. USI's address  
is USI ELECTRIC, INC./UNIVERSAL SECURITY INSTRUMENTS, INC.  
at 11407 Cronhill Drive, Suite A, Owings Mills, Maryland 21117, You  
must include a proof of purchase (receipt) along with the returned  
product.  
UNIVERSAL DOES NOT WARRANTAND SPECIFICALLY DISCLAIMS  
ANY WARRANTY, WHETHER EXPRESS OR IMPLIED, OF FITNESS  
FOR A PARTICULAR PURPOSE, OTHER THAN THE WARRANTY  
CONTAINED HEREIN. NO IMPLIED WARRANTY ON THIS PRODUCT,  
CREATED BY STATE LAW, SHALL EXTEND BEYOND THE TERM  
OF THIS WARRANTY UNLESS SUCH LAW OTHERWISE PROVIDES.  
UNIVERSAL SPECIFICALLY DISCLAIMS ANY LIABILITY AND SHALL  
NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL LOSS  
OR DAMAGE, INCLUDING, BUT NOT LIMITED TO, DAMAGES TO  
ANY EQUIPMENT WITH WHICH THIS PRODUCT IS USED.  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages so the above limitations or exclusions may not  
apply to you.  
No agent, representative, dealer, or employee of the company has the  
authority to increase or alter the obligations or terms of this Warranty.  
This Warranty gives you specific legal rights and you may also have  
other rights which vary from state to state.  
This Warranty is only valid for merchandise purchased from outlets in  
the United States and Canada. This warranty expires upon end-of-service  
life signal.  
Visit Us on the Web! www.UniversalSecurity.com  
11407 Cronhill Drive, Suite A  
Owings Mills, Maryland 21117 USA  
©2008 UNIVERSALSECURITY INSTRUMENTS, INC,. Rev. 2010  
288-3323-00E  
E
Printed in China  
 

Tascam Cassette Player 202mkIV User Manual
Tiffen Camera Accessories Glimmerglass Bronze Glimmerglass Filters User Manual
Toastess Hot Beverage Maker TJK 471 User Manual
Toastmaster Oven RST6 User Manual
Toshiba Projector 791U User Manual
Troy Bilt Snow Blower 31AE6GKF500 User Manual
Uniden Scanner APCO 25 User Manual
Uniflame Outdoor Fireplace WAD992SP User Manual
Verilux Microscope Magnifier VM02 User Manual
Vivitar Digital Camera 3765 User Manual